10-17
Channel Commands
PROBe:EXTernal:OFFSet
PROBe:EXTernal:OFFSet
Command
:CHANnel<N>:PROBe:EXTernal:OFFSet <offset_value>
The :CHANnel<N>:PROBe:EXTernal:OFFSet command sets the external
vertical value for the probe that is represented at the center of the display for
the selected channel. Offset parameters are probe and vertical scale dependent.
When using the 113xA, series probes, the CHANnel<N>:PROBe:STYPe
command determines how the offset is applied. When
CHANnel<N>:PROBe:STYPe SINGle is selected, the
:CHANnel<N>:PROBe:EXTernal:OFFset command changes the offset value of
the probe amplifier. When CHANnel<N>:PROBe:STYPe DIFFerential is
selected, the :CHANnel<N>:PROBe:EXTernal:OFFSet command changes the
offset value of the channel amplifier.
<N>
An integer, 1 - 4
<offset_value>
A real number for the offset value at center screen. Usually expressed in volts,
but can be in other measurement units, such as amperes, if you have specified
other units using the :CHANnel<N>:PROBe:EXTernal:UNITs command.
Example
This example sets the external offset for the probe on channel 1 to 0.125 in the
current measurement units:
10 OUTPUT 707;"CHANNEL1:PROBE:EXTERNAL ON"
20 OUTPUT 707;":CHANNEL1:PROBE:EXTERNAL:OFFSET 125E-3"
30 END
CHANnel<N>:PROBe:EXTernal command must be set to ON before issuing this
command or query or this command will have no effect.
Summary of Contents for Infiniium 8000A
