manualshive.com logo in svg

Agilent Technologies G7104A, User Manual

Share
Download
Agilent Technologies G7104A User Manual Download Page 58

58

Agilent 1290 Infinity II Flexible Pump User Manual

6

Error Information

General Error Messages

Compensation Sensor Short

Error ID: 0080

The ambient- compensation sensor (NTC) on the power switch board in the 
module has failed (open circuit).

The resistance across the temperature compensation sensor (NTC) on the 
power switch board is dependent on ambient temperature. The change in 
resistance is used by the leak circuit to compensate for ambient 
temperature changes. If the resistance across the sensor falls below the 
lower limit, the error message is generated.

Probable cause

Suggested actions

1

Defective power switch board

Please contact your Agilent service 
representative.

2

Loose connection between the power 
switch board and the main board

Please contact your Agilent service 
representative.

Summary of Contents for G7104A











































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands