manualshive.com logo in svg

Agilent Technologies G7104A, User Manual

Share
Download
Agilent Technologies G7104A User Manual Download Page 57

Agilent 1290 Infinity II Flexible Pump User Manual

57

Error Information

6

General Error Messages

Leak Sensor Open 

Error ID: 0083

The  leak  sensor  in  the  module has failed (open circuit).

The current through the leak sensor is dependent on temperature. A leak 
is detected when solvent cools the leak sensor, causing the leak- sensor 
current to change within defined limits. If the current falls outside the 
lower limit, the error message is generated.

Compensation Sensor Open

Error ID: 0081

The ambient- compensation sensor (NTC) on the power switch board in the 
module has failed (open circuit).

The resistance across the temperature compensation sensor (NTC) on the 
power switch board is dependent on ambient temperature. The change in 
resistance is used by the leak circuit to compensate for ambient 
temperature changes. If the resistance across the sensor increases above 
the upper limit, the error message is generated.

Probable cause

Suggested actions

1

Leak sensor not connected to the Power 
Switch board.

Please contact your Agilent service 
representative.

2

Defective leak sensor.

Please contact your Agilent service 
representative.

3

Leak sensor incorrectly routed, being 
pinched by a metal component.

Please contact your Agilent service 
representative.

Probable cause

Suggested actions

1

Loose connection between the power 
switch board and the main board

Please contact your Agilent service 
representative.

2

Defective power switch board

Please contact your Agilent service 
representative.

Summary of Contents for G7104A











































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands