manualshive.com logo in svg

Agilent Technologies E8364-60105, Installation Note, Page: 32 / 37

Share
Download
Agilent Technologies E8364-60105 Installation Note Download Page 32

32

  

                                                                                                                            

  

Installation Note E8364-90022

Step 9. Replace the Front Panel Nameplate and Overlay

Remove the Old Nameplate

1. Using a sharp object such as a knife blade, lift one end of the old nameplate (item 

①

). Be 

careful not to scratch the painted surface.

2. Using your fingers, pull the nameplate completely off of the front panel and discard it.

3. If any adhesive remains on the front panel surface, it can be removed by rubbing it with 

your finger. Do not use a sharp object to remove this adhesive. If necessary, the surface can 
be cleaned with isopropol alcohol.

Install the New Nameplate

1. Remove the protective backing from the new nameplate to expose the adhesive. Avoid 

touching the adhesive with your fingers as this may affect its ability to adhere to the front 
panel surface.

2.

Loosely

 align the new nameplate over the recess in the front panel and apply lightly.

3. Once the nameplate is properly aligned, press it firmly onto the surface to secure it.

Figure 23

Model Number Nameplate Replacement

NOTE

The figure above shows the E8364B front panel and floppy disk drive. The 
E8364C front panel has a slightly different appearance and does not 
include a floppy disk drive. 

Summary of Contents for E8364-60105






































Reviews:

No comments