manualshive.com logo in svg

Agilent Technologies E8363BU/CU-068, Installation Note, Page: 7 / 46

Share
Download
Agilent Technologies E8363BU/CU-068 Installation Note Download Page 7

Installation Note E8364-90023                                                                                                                         

 

7

Items Included in the Upgrade Kit

Check the contents of your kit against the following list. If any item is missing or damaged, 
contact Agilent Technologies. Refer to 

“Contacting Agilent” on page 3

.

Table 1

Contents of Option 068 Upgrade Kit (E8364-60106)

Ref.

Desig.

Description

Qty

 Part Number

Installation note (this document)

1

E8364-90023

Entitlement Certificate

1

5964-5145

ROHS addendum

1

9320-6722

Model number nameplate (for 67 GHz analyzer E8361A)

1

E8361-80001

Model number nameplate (for 67 GHz analyzer E8361C)

1

E8361-80006

Lower front panel overlay (Option 014)

1

E8361-80004

A12

Source 20

1

E8361-60002

A17

LOMA 12

1

5087-7247

A18

MA 24

1

5087-7248

A20

LODA 1

5087-7777

A22

Switch

1

5087-7238

A23

SOMA 70, port 1

2

5087-7249

A24

SOMA 70, port 2

A25

Test port 1 coupler

2

5087-7225

A26

Test port 2 coupler

A27

Channel A first converter (mixer)

4

5087-7258

A28

Channel R1 first converter (mixer)

A29

Channel R2 first converter (mixer)

A30

Channel B first converter (mixer)

Mixer bias board

1

E8361-63044

SOMA 70 bracket

2

E8361-00002

Machine screw M3.0 x 10 (for attaching A22 switch)

2

0515-0374

Machine screw M3.0 x 6 (for attaching SOMA 70 brackets)

6

0515-0430

Machine screw M3.0 x 25 (for attaching SOMA 70s to brackets)

4

0515-0667

Summary of Contents for E8363BU/CU-068















































Reviews:

No comments