manualshive.com logo in svg

Agilent Technologies 81618A, User Manual, Page: 26 / 114

Share
Download
Agilent Technologies 81618A User Manual Download Page 26

Definition of Terms

Specifications

Agilent  81618A/9A and Agilent 81622B/3B/4B/6B/7B/8B User’s Guide, Second Edition

25

Conditions:

 constant wavelength,  constant power level, angled 

connector as specified, linewidth of source <100 MHz,  temperature as 

specified.

N O T E

Spectral ripple is measured by stepping the source wavelength over 

the wavelength range specified.

Relative uncertainty due to speckle noise

This is the uncertainty of the power reading when using a coherent 

source. This is due to a variation of the power meters responsivity 

caused by optical interference

1

 between different optical paths within 

the power meters optical assembly.

Conditions:

 constant wavelength, constant power level, angled 

connector as specified, linewidth of source as specified, temperature 

as specified.

1

 Incoming light to the integrating sphere undergoes numerous 

internal reflections (as many as several hundred) prior to hitting 

the detector. If the source is sufficiently coherent, a complicated 

interference pattern (speckle pattern) appears spread over the 

whole sphere volume. Slight changes of the ambient conditions 

(temperature, vibration, shock) affect particular optical paths 

which consequently changes the speckle pattern and results in an 

instability of the head power reading (speckle noise).

N O T E

Changes in the source wavelength have a similar effect on speckle 

noise as environmental changes, because they cause fluctuations in 

the interference pattern. If the source coherence length is small 

compared to the effective path length, the interference pattern 

disappears and relative uncertainty due to speckle noise becomes 

negligible.

Measurement:

 In contrast to the spectral ripple definition the source 

wavelength isn’t stepped when measuring speckle noise.

Relative uncertainty due to polarization

Also termed polarization-dependent responsivity (PDR), the relative 

uncertainty due to polarization is the uncertainty of the displayed 

power level on the input polarization state, expressed as the difference 

between the highest and the lowest displayed power.  Uncertainty 

figures are based upon a 95% confidence level.

Conditions:

 laser source with variable polarization state, generation of 

all possible polarization states (covering the entire Poincaré sphere), 

constant wavelength, constant power level, angled connector as 

specified, temperature as specified.

Summary of Contents for 81618A



















































































































Reviews:

No comments