manualshive.com logo in svg

Agilent Technologies 708-DS, Operator'S Manual

Share
Download
Agilent Technologies 708-DS Operator'S Manual Download Page 82

82

708-DS / 709-DS Operator’s Manual

4

Operating the 708-DS / 709-DS

 

Menu Screen - Instrument

Menu Screen - Instrument Settings Screen 1

Table 6

Menu Screen - Instrument Settings Screen 1

Option

Function

Tester ID

A twelve-character field that helps identify the instrument. The Tester 
ID is printed out with the other system information during a test.

Comm ID

The address of the instrument on the communications bus. This address 
is used by external host programs to communicate with the instrument. 
The Comm ID may range from 01 to 99.

All Position Spin

Allows the spindle to rotate regardless of the position of the drive unit. 
This is useful when calibrating spindle speed as the spindle may rotate 
while the drive unit is in its upper position. If this option is not checked, 
the spindle only rotates when the drive unit is in its lowest position.

Summary of Contents for 708-DS













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands