manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 96

96

5977B Series MSD Troubleshooting and Maintenance Manual

4

General Maintenance

Maintaining the Vacuum System

Periodic maintenance

Some maintenance tasks for the vacuum system must be performed 
periodically. (See 

Table 9

 on page 91.) These include:

•

Checking the foreline pump fluid (every week)

•

Checking the calibration vial (every 6 months)

•

Replacing the foreline pump oil (every 6 months; every 3 months for 
CI MSDs using ammonia reagent gas, standard foreline pump)

•

Tightening the foreline pump oil box screws (first oil change after 
installation, standard foreline pump)

•

Changing the foreline pump exhaust filters

•

Replacing the DP fluid (once a year)

•

Changing the dry foreline pump tip seal (once a year)

Failure to perform these tasks as scheduled can result in decreased 
instrument performance. It can also result in damage to your instrument.

Other procedures

Tasks such as replacing a Micro-Ion vacuum gauge should be performed only 
when needed. (See

 “General Troubleshooting” 

on page 35.) Refer to the online 

help in the Agilent MassHunter GC/MS Acquisition software for symptoms 
that indicate this type of maintenance is required.

More information is available

If you need more information about the locations or functions of vacuum 
system components. (See

 “Vacuum System” 

on page 153.)

Most of the procedures in this chapter are illustrated with video clips on the 
5977B Series MSD User Information media.

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands