manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 61

General Troubleshooting

2

5977B Series MSD Troubleshooting and Maintenance Manual

61

Contamination

Contamination is usually identified by excessive background in the mass 
spectra. It can come from the GC or from the MSD. The source of the 
contamination can sometimes be determined by identifying the contaminants. 
Some contaminants are much more likely to originate in the GC. Others are 
more likely to originate in the MSD.

Contamination originating in the GC typically comes from one of these 
sources:

•

Column or septum bleed

•

Dirty GC inlet

•

GC inlet liner

•

Contaminated syringe

•

Poor quality carrier gas

•

Dirty carrier gas tubing

•

Fingerprints (improper handling of clean parts)

Contamination originating in the MSD typically comes from one of the 
following sources:

•

Air leak

•

Cleaning solvents and materials

•

Foreline pump oil (standard foreline pump)

•

Fingerprints (improper handling of clean parts)

Table 6 

on page 62 lists some of the more common contaminants, the ions 

characteristic of those contaminants, and the likely sources of those 
contaminants.

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands