manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 54

54

5977B Series MSD Troubleshooting and Maintenance Manual

2

General Troubleshooting

Error Messages

Sometimes, a problem in your MSD will cause an error message to appear in 
the MSD Data Acquisition software. Some error messages appear only during 
tuning. Other messages may appear during tuning or data acquisition.

Some error messages are latched. Latched messages remain active in your 
data system even if the condition that caused the message has corrected itself. 
If the cause is removed, these messages can be removed by checking 
instrument status through the data system.

Difficulty in mass filter electronics

•

Pressure in the analyzer chamber is too high

•

RFPA is not adjusted correctly

•

Mass filter (quad) contacts are shorted or otherwise not working correctly

•

Mass filter is not working correctly

•

MSD electronics are not working correctly

Difficulty with the electron multiplier supply

•

Large peak, such as the solvent peak, eluted while the analyzer was on

•

Pressure in the analyzer chamber is too high

•

MSD electronics are not working correctly

Difficulty with the fan

If a cooling fan fault occurs, the vacuum control electronics automatically shut 
off the high vacuum pump, the ion source, and the mass filter heaters. The 
message: 

The system is in vent state

 may also appear. It is important to note 

that even though the high vacuum pump is off, the analyzer chamber may not 
actually be vented. See

 “The system is in vent state” 

on page 58 for precautions 

to take.

•

One of the fans is disconnected

•

One of the fans has failed

•

MSD electronics are not working correctly

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands