manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 38

38

5977B Series MSD Troubleshooting and Maintenance Manual

2

General Troubleshooting

General Symptoms

This section describes symptoms you might observe when first turning on the 
GC/MSD system, and their possible causes. Any of these symptoms would 
prevent operation of the system.

GC does not turn on

Nothing happens when the GC is switched on. The GC fans do not turn on, and 
the keypad display does not light.

•

Disconnected GC power cord

•

No voltage or incorrect voltage at the electrical outlet

•

Failed fuse in the GC

•

GC power supply is not working correctly

MSD does not turn on

Nothing happens when the MSD is switched on. The foreline pump does not 
start. The cooling fan for the high vacuum pump does not turn on.

•

Disconnected MSD power cord

•

No voltage or incorrect voltage at the electrical outlet

•

Failed primary fuses

•

MSD electronics are not working correctly

Foreline pump is not operating

The MSD is receiving power (the fan is operating), but the foreline pump is not 
operating.

•

Large air leak (usually the analyzer door open) has caused pumpdown 
failure. See

 “Pumpdown failure shutdown” 

on page 156. You must power 

cycle the MSD to recover from this state.

•

Disconnected foreline pump power cord

•

Malfunctioning foreline pump

•

Check power switch on foreline pump

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands