Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 234

Page: 234 / 258

234

5977B Series MSD Troubleshooting and Maintenance Manual

Parts

IDP3 Dry foreline pump and related parts

Table 21

IDP3 foreline pump and related parts (

Figure 57

)

Description

Part number

Foreline hose assembly (hose and internal spring)

05971-60119

•

Hose Clamp

†

used with 05971-60119

†

Hose clamps are interchangeable, but give an optimum fit if they are matched

1400-3241

Dry foreline pump

G3870-60600

Replace tip seal set, non-ammonia

IDP3TS

Solid tip seal kit, inert

G3870-67000

KF10/16 Clamp (foreline inlet), Micro-Ion vacuum gauge

0100-1397

KF16 Hose adapter

G1099-20531

Vibration Isolation kit

IDP3VIBISOKIT

Exhaust hose

G3170-60100

Exhaust adapter

G3170-80029

Barbed fitting

G3170-80006

Exhaust hose for oil-less pump

G3170-60100

Summary of Contents for 5977B Series



































































































































































































































































Search results

Summary of Contents for 5977B Series

Reviews:

Brands by name

Popular brands

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Search results

Summary of Contents for 5977B Series

Reviews:

Brands by name

Popular brands