manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 228

228

5977B Series MSD Troubleshooting and Maintenance Manual

9

Parts

To Order Parts

To order parts for your MSD, contact your local Agilent Technologies office. 
Supply them with the following information:

Model and serial number of your MSD, located on a label on the lower left side 
near the front of the instrument. 

•

Part number(s) of the part(s) needed

•

Quantity of each part needed

Some parts are available as rebuilt assemblies

Rebuilt assemblies pass all the same tests and meet all the same specifications 
as new parts. Rebuilt assemblies can be identified by their part numbers. 

The first two digits of the second part of the part number are 69 or 89 (such as 
xxxxx-69xxx or xxxxx-89xxx). Rebuilt assemblies are available on an 
exchange-only basis. When you return the original part to Agilent 
Technologies (after you receive the rebuilt assembly), you will receive a credit.

If you cannot find a part you need

If you need a part that is not listed in this chapter, check the Agilent 
Technologies Analytical Supplies Catalog or the on-line catalogue on the 
worldwide web at 

http://www.agilent.com/chem

. If you still cannot find it, 

contact your Agilent Technologies service representative or your Agilent 
Technologies office. 

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands