manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 221

Electronics

8

5977B Series MSD Troubleshooting and Maintenance Manual

221

Back Panel and Connectors

The back panel (See 

Figure 53

 on page 223) contains several connectors, the 

primary fuses, and several status LEDs. Most of these components are part of 
the AC board or the LAN/MS control card, and extend through the back panel.

HI-VAC SIGNAL

The high vacuum signal connector is on the AC board. See

 “Turbo pump 

control” 

on page 217and

 “Diffusion pump control” 

on page 217.

HI-VAC POWER

The high vacuum power connector carries power for the diffusion pump 
heater or the turbo controller from the AC board. 

Primary fuses

The primary fuses limit current into the MSD in case of a short circuit in the 
foreline pump. The primary fuses are on the AC board.

Power cord receptacle

The AC power cord brings in all electrical power for the MSD. The power cord 
can be detached from the MSD.

FORELINE PUMP

The foreline pump power cord receptacle provides AC power for the foreline 
pump. If the power switch is off, no power is supplied to the foreline pump.

REMOTE

The remote start connector is the external connector for the remote start 
circuitry on the LAN/MS control card. It receives remote start signals from the 
GC.

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands