manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 220

220

5977B Series MSD Troubleshooting and Maintenance Manual

8

Electronics

Power Supplies

Low voltage (AC-DC) power supply

The low voltage power supply is mounted next to the toroid transformer in the 
electronics module. A universal input power supply, it converts AC line voltage 
into the DC voltages used by the rest of the electronics. The power supply 
generates the following DC voltages:

•

+24 V (nominal)

•

+15 V (nominal)

•

–15 V (nominal)

•

+5 V (nominal)

High voltage (HED) power supply

The high voltage power supply provides the –10,000 V DC for the high energy 
dynode (HED) in the detector for the EI MSD. The EI/PCI/NCI MSD requires a 
bipolar power supply that can also p10,000 V for NCI operation. The 
HED power supply also provides 600 VDC for the detector focus lens. Due to 
the high impedance of this circuit, measuring the detector focus voltage with a 
handheld voltmeter will give a typical reading of 90 to 100 V where the 
polarity matches that of the HED voltage.

Toroid transformer

The toroid transformer is mounted next to the AC board. It provides 24 VAC 
for the mass filter and source heater circuits. The input wires take 120 VAC or 
200 to 260 VAC from the AC board. The AC board samples the line voltage and 
uses a relay to appropriately strap the toroid primary. The output wires 
connect to the main board.

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands