manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 219

Electronics

8

5977B Series MSD Troubleshooting and Maintenance Manual

219

LAN/MS Control Card

The LAN/MS control card is located to the left of the main board on the 
electronics panel. The LAN/MS control card has two main functions:

•

Providing a communication interface between the MSD and the data system

•

Providing real-time control of the MSD, freeing the data system for other 
tasks

Functional areas of the LAN/MS control card include:

•

Instrument controller

•

Data processor

•

Main processor

•

Serial communication processor

•

Network communication controller

•

Remote start processor

•

Random access memory (RAM)

•

Status LEDs

•

Local Control panel firmware

•

Mini display module

LEDs on the LAN/MS control card are visible on the rear panel. The upper two 
LEDs indicate network communication. 

The two bottom LEDs are the power (On, digital 5 V) and the heartbeat 
indicator. The flashing heartbeat LED indicates that the operating system of 
the MSD is functioning. In case of catastrophic loss of flash memory, the 
heartbeat flashes in an SOS (•••

– – –

 •••) pattern.

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands