manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 215

Electronics

8

5977B Series MSD Troubleshooting and Maintenance Manual

215

Electronics Module

Most of the electronics in the MSD are contained in the electronics module. 
The whole electronics module can be replaced, if necessary, by your Agilent 
Technologies service representative.

The electronics module contains:

•

Main board

•

Signal amplifier board

•

LAN/MS control card

•

AC board (power distribution/vacuum control board)

•

Low voltage (AC-DC) power supply

•

High voltage (HED) power supply

•

Toroid transformer assembly

•

Lens driver board for HES

Main board

The main board is mounted on the outer side of the electronics module. The 
main board performs these functions:

•

Receives and decodes digital instructions from the LAN/MS control card.

•

Sends digital information to the LAN/MS control card.

•

Generates voltages for the ion source lenses.

•

Generates control signals for filament selection, filament emission current, 
and electron energy. Generates control signals for quadrupole RF drive, 
quad frequency adjustment, DC polarity selection, and all detector voltages.

•

Performs analog-to-digital conversion for the Direct signal, ion source and 
mass filter temperature signals, and foreline pressure or turbo pump speed 
signal.

•

Monitors the signals from the vacuum system and fans and the filament 
status, HV fault and RF fault signals from the side board. Activates the 
shutdown line when the analyzer electronics must be disabled.

•

Generates the control signals (on and off) used by the AC board for the high 
vacuum pump and calibration valve.

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands