manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 205

Analyzer

7

5977B Series MSD Troubleshooting and Maintenance Manual

205

DC polarity

The DC polarity (DC Pol) parameter selects the orientation of the direct 
current applied to the quadrupole mass filter. The DC Pol that works best for 
your MSD is determined at the factory. It is listed on the final test sheet 
accompanying your MSD. It is also listed on a label on the cover over the RF 
coils. This cover can be viewed by removing the upper MSD cover.

Mass (axis) gain

Mass gain (MassGain) controls the mass assignment, that is, assignment of a 
particular peak to the correct 

m/z

 value.

•

A higher gain yields higher mass assignment.

•

Mass gain affects peaks at high masses more than peaks at low masses.

Mass (axis) offset

Mass offset (MassOffs) also controls the mass assignment.

•

A higher offset yields higher mass assignment.

•

Mass offset generally affects peaks equally at all masses.

Quadrupole maintenance

The mass filter requires no periodic maintenance. It should not be removed 
from the radiator. If 

absolutely

 necessary (that is, if the only alternative is 

replacement), the quadrupole can be cleaned. Cleaning 

must

 be performed by 

Agilent Technologies service personnel.

C A U T I O N

Using the nonpreferred DC polarity may result in very poor performance. Always use 
the factory-specified polarity.

C A U T I O N

Never put the quadrupole in an ultrasonic cleaner.

Never change the physical orientation of the quadrupole mass filter.

The fused-quartz quadrupole is fragile and will break if dropped or handled roughly. 

The material in the cusps of the quadrupole is very hygroscopic. If exposed to water, 
the quadrupole must be dried very slowly to prevent damage. 

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands