manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 195

Analyzer

7

5977B Series MSD Troubleshooting and Maintenance Manual

195

CI Ion Source

The CI ion source is similar in shape to the traditional EI ion source, but only 
has one part in common with the EI ion source — the entrance lens. The single 
CI filament has a straight wire and a reflector. A “dummy” filament provides 
connections for the other wires.

The holes in the ion source (electron-entrance and ion-exit) are very small 
(0.5 mm), making it possible to pressurize the ionization chamber. Both the 
source body and the plate are at repeller potential, electrically isolated from 
the radiator and the interface tip. The seal for the interface tip (

Figure 46

 on 

page 196) ensures a leak-tight seal and electrical isolation between the CI 
interface and ion source.

Ion source body

Figure 45  

CI ion source structure

Entrance lens

Filament

Drawout cylinder

Drawout plate

Dummy filament

Ion focus lens

Lens insulation

Repeller

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands