manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 175

Vacuum System

6

5977B Series MSD Troubleshooting and Maintenance Manual

175

Turbo Pump and Fan

The turbo pump is clamped directly to the bottom of the analyzer chamber. 

The turbo pump has a cylindrical body with its inlet open to the interior of the 
analyzer chamber. Inside the pump body is a central shaft or cylinder. Sets of 
small blades (airfoils) radiate from the central shaft. The shaft spins at up to 
60,000 revolutions per minute (rpm) in the turbo pump.

Turbo pumps move gas by momentum transfer. The turbine blades are angled 
so that when they strike a gas molecule it is deflected downward. Each set of 
blades pushes the gas molecules further down toward the pump outlet. 

The foreline pump is connected by a hose to the outlet of the turbo pump. 

It removes the gas molecules that reach the outlet.

A controller regulates current to the pump and monitors pump motor speed 
and temperature. A cooling fan is located between the turbo pump and the 
front panel of the MSD. The fan draws air from outside the MSD and blows it 
over the pump.

The turbo pump automatically turns on when the MSD power is switched on. 
The system allows the analyzer to be turned on when the turbo pump is 
greater than 80% speed, but the pump normally operates at 100% speed. Turbo 
pump MSDs typically maintain an indicated pressure below 8 × 10

-5

 Torr for 

helium column flows up to 4 mL/minute for the performance turbo pump, and 
up to 2 mL/minute for the standard turbo pump. Pressure (vacuum) can only 
be measured if your MSD is equipped with the optional gauge controller.

The turbo pump spins up (starts) and spins down (stops) quickly. This 
simplifies pumpdown and venting. From initial power-on, the system can 
pump down to operating pressure in 5 to 10 minutes. 

See Also

•

To pump down the MSD in the Operating Manual

•

To vent the MSD in the Operating Manual

•

See

 “Turbo pump control” 

on page 217.

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands