manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 168

168

5977B Series MSD Troubleshooting and Maintenance Manual

6

Vacuum System

Foreline Gauge

The foreline gauge monitors the pressure (vacuum) at the exit of the diffusion 
pump. The primary function of the foreline gauge is diffusion pump control. 
When the foreline pump has reduced the pressure in the analyzer chamber to 
below 300 mTorr (0.3 Torr), the diffusion pump is automatically switched on. 
If the foreline pressure rises above 400 mTorr (0.4 Torr), the AC board 
switches off the diffusion pump heater and the analyzer electronics.

Monitor the foreline pressure from the data system or the LCP.

The foreline gauge is used only with diffusion pump MSDs.

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands