manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 161

Vacuum System

6

5977B Series MSD Troubleshooting and Maintenance Manual

161

High Vacuum Pump

Diffusion pump system

The diffusion pump supports a maximum flow rate of 1.5 mL/min into the 
MSD. The diffusion pump uses baffling to prevent vapor from migrating into 
the analyzer chamber. Foreline pressure is monitored by the foreline gauge. 
The AC board controls the diffusion pump heater.

Turbo pump system

The 5977B Series MSD supports a turbo pump. The turbo pump has a screen to 
keep debris out of the pumpbut no baffle is necessary. Pump speed is 
controlled by the turbo controller; there is no foreline gauge.

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands