manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 154

154

5977B Series MSD Troubleshooting and Maintenance Manual

6

Vacuum System

Overview

The vacuum system creates the high vacuum (low pressure) required for the 
MSD to operate. Without the vacuum, the molecular mean free path would be 
very short and ions would collide with air molecules before they could reach 
the detector. Operation at high pressures also would damage analyzer 
components.

The 5977B Series MSDs use two vacuum pumps to obtain the vacuum levels 
needed. One of two foreline pumps (standard or dry) creates a low vacuum, 
then a high vacuum pump engages to create the vacuum needed for 
operation.The 5977B Series MSD uses one of two kinds of high vacuum pumps: 
a diffusion pump or a turbomolecular (turbo) pump. The pump type 
determines the maximum column flow supported by the MSD. The 5977B HES 
Series MSD model G7079B uses a turbomolecular (turbo) pump for high 
vacuum. It has a maximum column flow rate of 4.0 mL/min.

Most vacuum system operation is automated. Operator interaction is through 

the data system or control panel. Monitor the vacuum system through the data 
system or GC control panel.

Table 10  

Recommended maximum flow rates by model

Model number

Description

Maximum recommended 
column flow

G7080B

Diffusion pump, EI

1.5 mL/min

G7077B

Turbo pump, EI

4.0 mL/min

G7078B

Turbo pump, EI

4.0 mL/min

G7081B

Turbo pump, EI

4.0 mL/min

G7079B

Turbo pump, EI HES

4.0 mL/min

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands