manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 149

CI Maintenance

5

5977B Series MSD Troubleshooting and Maintenance Manual

149

To Clean the Reagent Gas Supply Lines

Materials needed

•

Clean, dry nitrogen

•

Heat gun

•

Tubing cutter (8710-1709)

Procedure

If the reagent gas lines become contaminated, they can be cleaned.

1

Disconnect the reagent gas tubing from the gas supply, the gas purifier, and 
the MSD. 

2

Cap the gas purifier following the instructions on the label.

3

Connect one end of the tubing to a supply of clean, dry nitrogen and turn 
on the gas flow.

4

Use the heat gun to warm the tubing, starting at the supply end and 
working your way to the free end.

5

Repeat for any other pieces of tubing that need to be cleaned.

6

Reconnect the tubing to the gas supply, gas purifier, and MSD. Follow the 
instructions on the gas purifier label.

WA R N I N G

Do not heat the gas tubing when reagent gas is flowing.

C A U T I O N

Do not put liquids into the tubing. Do not heat the tubing when it is connected to the 
MSD.

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands