manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 141

General Maintenance

4

5977B Series MSD Troubleshooting and Maintenance Manual

141

Maintaining the Electronics

Scheduled maintenance

None of the electronic components of the MSD need to be replaced on a 
regular schedule. None of the electronic components in the MSD need to be 
adjusted or calibrated on a regular schedule. Avoid unnecessary handling of 
the MSD electronics.

Electronic components

Very few of the electronic components are operator serviceable. The primary 
fuses can be replaced by the operator. The RF coils can be adjusted by the 
operator. All other maintenance of the electronics should be performed by 
your Agilent Technologies service representative.

Electrostatic precautions

All of the printed circuit boards in the MSD contain components that can be 
damaged by electrostatic discharge (ESD). Do not handle or touch these 
boards unless absolutely necessary. In addition, wires, contacts, and cables 
can conduct ESD to the printed circuit boards to which they are connected. 
This is especially true of the mass filter (quadrupole) contact wires which can 
carry ESD to sensitive components on the side board. ESD damage may not 
cause immediate failure, but it will gradually degrade the performance and 
stability of your MSD.

When you work on or near printed circuit boards, or when you work on 
components with wires, contacts, or cables connected to printed circuit 
boards, always use a grounded antistatic wrist strap and take other antistatic 

WA R N I N G

Improper use of these procedures could create a serious safety hazard. Improper use 
of these procedures could also result in serious damage to, or incorrect operation of, 
the MSD.

WA R N I N G

Vent the MSD and disconnect its power cord before performing any of these 
procedures 

except

 adjusting the RF coils.

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands