manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 137

General Maintenance

4

5977B Series MSD Troubleshooting and Maintenance Manual

137

To Lubricate the Side Plate O-Ring

Materials needed

•

Cloths, clean (05980-60051)

•

Gloves, clean, lint-free

•

Large (8650-0030)

•

Small (8650-0029)

•

Grease, Apiezon L, high vacuum (6040-0289)

The side plate O-ring needs a thin coat of grease to ensure a good vacuum seal. 
If the side plate O-ring appears dry or does not seal correctly, lubricate it using 
this procedure. A good test is to wipe off the side plate with methanol, then 
close the analyzer chamber. If the O-ring has enough grease on it, it will leave a 
faint trace on the side plate.

Procedure

1

Vent the MSD. 

2

Open the analyzer chamber. 

3

Use a clean, lint-free cloth or glove to spread a 

thin

 coat of high vacuum 

grease only on the exposed surface of the O-ring. (See 

Figure 20

 on 

page 138.)

4

Use a clean, lint-free cloth or glove to wipe away excess grease. If the 
O-ring looks shiny, there is too much grease on it.

5

Close the analyzer chamber. 

6

Pump down the MSD. 

C A U T I O N

Vacuum seals other than the side plate O-ring and vent valve O-ring do not need to be 
lubricated. Lubricating other seals can interfere with their correct function.

    

             

C A U T I O N

Do not use anything except the recommended vacuum grease. Excess grease can trap 
air and dirt. Grease on the surface of the O-ring other than the exposed surface can trap 
air, resulting in air spikes during operation.

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands