manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 133

General Maintenance

4

5977B Series MSD Troubleshooting and Maintenance Manual

133

To Replace the Fan for the High Vacuum Pump

Materials needed

Fan (G7005-60564)

Screwdriver, Torx T-20 (8710-1615)

Procedure

1

Vent the MSD. 

2

Remove the left side MSD cover. 

3

Disconnect the fan wiring from the connector on the MSD frame. (See 

Figure 19

 on page 134.)

4

Remove the four fan screws and the safety grill. Remove the fan. Keep the 
screws.

5

Install the new fan with the flow arrow on the side pointing toward the 
pump. The wires should be at the upper left, close to the connector.

6

Add the safety grill and the four screws. Tighten the screws firmly.

7

Connect the fan wiring to the fan connector on the MSD frame.

8

Reinstall the MSD covers.

9

Pump down the MSD. 

    

             

WA R N I N G

Do not touch the high vacuum pump. The pump could still be hot enough to burn you.

WA R N I N G

Ensure the safety grill that shields the fan blades is in place.

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands