manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 123

General Maintenance

4

5977B Series MSD Troubleshooting and Maintenance Manual

123

To Install the DP

Materials needed

•

Gloves, oil-resistant

•

Vacuum cleaner, non-ESD generating (92175V or equivalent)

This procedure works best with two people, one to hold the pump, and one to 
install the clamp.

Procedure

1

Vacuum the fan that cools the DP.

Keeping the fan clean helps ensure maximum cooling. This is one of the 
few times you will have convenient access to the pump side of the fan.

2

Slide the DP into the MSD.

You may have to tilt the pump slightly to get it into the MSD. Do not tilt it 
past 45 degrees.

3

Install the O-ring assembly on the DP. (See 

Figure 16

 on page 124.)

4

Lift the DP into its normal position.

5

Install the KF50 clamp.

6

Reconnect the DP temperature sensor wires to the wiring harness.

7

Reconnect the high vacuum power cable to the HIVAC POWER connector 
on the back panel of the MSD. This is the thick black cable that emerges 
near the bottom of the pump.

8

Reconnect the foreline gauge fitting to the outlet of the DP.

If you disconnected the foreline gauge cable, reconnect it to the foreline 
gauge.

9

Move the MSD back to its normal position. 

    

             

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands