manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 116

116

5977B Series MSD Troubleshooting and Maintenance Manual

4

General Maintenance

To Check the DP Fluid

Materials needed

•

Screwdriver, Torx T-20 (8710-1615)

Procedure

1

Remove the analyzer window cover.

2

Vent the MSD.

3

Remove the side cover.

4

Check the DP fluid level. (See 

Figure 13

 on page 117.)

The DP fluid level can be seen through the window below the fan at the 
front of the MSD. The DP fluid level should be between the top and bottom 
of one of the 

FULL

 ranges. There are two sets of marks. Use the 

HOT

 marks if 

the DP is on and is at its normal operating temperature. Use the 

COLD

 

marks if the pump is off and has had time to cool. If the fluid level is below 
the bottom of the appropriate range, replace the DP fluid. Do not just add 
fluid.

The pump fluid should be clear or almost clear. Dark or cloudy pump fluid 
indicates an air leak or excessive heat. If the pump fluid appears dark or 
cloudy, replace it. Then, check for an air leak.

The DP fluid should be replaced at least once a year, or more often if the 
pump fluid level is low, or if the fluid is dark or cloudy.

    

             

WA R N I N G

Do not remove any other covers. Removing other covers may expose hazardous 
voltages.

WA R N I N G

Keep your hair away from the cooling fan if the MSD is turned on.

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands