Agilent Technologies 5977B CI MSD Operating Manual Download Page 187 | Manualshive

Page: 187 / 254

background image

7

General Maintenance



To Assemble the EI HES

5977B Series MSD Operating Manual

187

To Assemble the EI HES

Materials needed

•

Gloves, clean, lint-free

•

Large (8650-0030)

•

Small (8650-0029)

•

T6 Torx driver, (8710-2548)

•

Tweezers (8710-2460)

Procedure

Refer to the exploded parts view

and the EI HES parts list

page 190 while using this procedure.

1

Assemble the five lenses inside the lens insulator. (See

page 188.) The lens number is engraved into the outer circumference of each
lens.

a

Starting with the entrance lens 1, set the lens into the end groove in the
lens insulator, and rotate the lens until you feel the ball seat into the
circular recess.

b

Insert the next 4 lenses, in numerical order, into the lens insulator. The
lens chamber open end always faces the entrance lens 1. Rotate each
lens until you feel the ball seat into the circular recess.





It is easier to insert lens 5 on an angle because the lens stack at this
point makes the lens insulator less flexible.

CAUTION

Always wear clean gloves when working in the analyzer chamber to avoid
contamination.

CAUTION

Use care when inserting the lenses into the lens insulator casing. Putting
excessive stress on this casing can break or crack it. If this happens, do not
attempt to operate with a defective lens insulator, it must be replaced.

«
...
185
186
187
188
189
...
»

Summary of Contents for 5977B CI MSD































































































































































































































































Reviews:

No comments

Related manuals for 5977B CI MSD

Brand: Calpeda Pages: 16

Brand: Eaton Pages: 20

Brand: Eaton Pages: 21

Brand: Jandy Pages: 16

Brand: PerformancePro Pages: 15

Brand: AL-KO Pages: 144

Brand: Acquaer Pages: 12

Brand: SAMES KREMLIN Pages: 51

Brand: A.O. Smith Pages: 4

Brand: Battery Watering Technologies Pages: 2

Brand: Navien Pages: 131

Summit Pumper Vacuum

Brand: Alto Pages: 6

Brand: Quantum Pages: 36

Brand: Faber Pages: 9

Brand: Alpine Pages: 20

Brand: Bard Pages: 41

Brand: Hi-Force Pages: 16

Brand: Ocean Aire Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands