manualshive.com logo in svg

Agilent Technologies 5977B CI MSD, Operating Manual

The Agilent Technologies 5977B CI MSD is an advanced scientific instrument offering precise and reliable mass spectrometry analysis. To ensure optimal usage, download the comprehensive Operating Manual for free from our website. This user-friendly manual provides detailed instructions and troubleshooting insights for maximizing the capabilities of the 5977B CI MSD.

Share
Download
background image

7

General Maintenance

Before Starting

5977B Series MSD Operating Manual

171

install a hose to take the exhaust from the foreline pump outdoors or into a fume 
hood vented to the outdoors. For the standard foreline pump, this requires 
removing the oil trap. Be sure to comply with your local air quality regulations.

The fluids in the diffusion pump and standard foreline pump also collect traces 
of the samples being analyzed. All used pump fluid should be considered 
hazardous and handled accordingly. Dispose of used fluid correctly, as specified 
by your local regulations.

Ion source cleaning

The main effect of operating the MSD in CI mode is the need for more frequent 
ion source cleaning. In CI operation, the ion source chamber is subject to more 
rapid contamination than in EI operation because of the higher source pressures 
required for CI.

Electrostatic discharge

All of the printed circuit boards in the MSD contain components that can be 
damaged by electrostatic discharge (ESD). Do not handle or touch these boards 
unless absolutely necessary. In addition, wires, contacts, and cables can conduct 
ESD to the electronics boards to which they are connected. This is especially true 
of the mass filter (quadrupole) contact wires which can carry ESD to sensitive 
components on the side board. ESD damage may not cause immediate failure, 
but it will gradually degrade the performance and stability of your MSD.

WARNING

The oil trap supplied with the standard foreline pump stops only foreline pump 
oil. It does not trap or filter out toxic chemicals. If you are using toxic solvents 
or analyzing toxic chemicals, remove the oil trap. Do not use the trap if you 
have a CI MSD. Install a hose to take the foreline pump exhaust outside or to a 
fume hood.

WARNING

When replacing pump fluid, use appropriate chemical-resistant gloves and 
safety glasses. Avoid all contact with the fluid.

WARNING

Always perform any maintenance procedures using hazardous solvents under 
a fume hood. Be sure to operate the MSD in a well-ventilated room.

Summary of Contents for 5977B CI MSD































































































































































































































































Reviews:

No comments

Related manuals for 5977B CI MSD

Navien CR-180 Installation Manual preview
CR-180
Brand: Navien Pages: 60
Saci SIGMA Installation And Maintenance Manual preview
SIGMA
Brand: Saci Pages: 24
PAC AL Installation & Operation Manual preview
AL
Brand: PAC Pages: 30
Calpeda MGP Original Operating Instructions preview
MGP
Brand: Calpeda Pages: 4
Gamo PCP Instruction Manual preview
PCP
Brand: Gamo Pages: 25
Gamma Vacuum TSP User Manual preview
TSP
Brand: Gamma Vacuum Pages: 27
ICON iSOLAR PDP Series Manual preview
iSOLAR PDP Series
Brand: ICON Pages: 24
JBG HT ZHHS-01-10K-R290-V5-M Service Manual preview
ZHHS-01-10K-R290-V5-M
Brand: JBG HT Pages: 32
Aspen Pumps mini aqua pump Installation & Maintenance Manual preview
mini aqua pump
Brand: Aspen Pumps Pages: 13
Ferroli AQUA PLUS 200 LT Installation And Maintenance Manual preview
AQUA PLUS 200 LT
Brand: Ferroli Pages: 96
Modine Manufacturing GEO16-501.4 Installation And Service Manual preview
GEO16-501.4
Brand: Modine Manufacturing Pages: 28
Bard WH423D Installation Instructions Manual preview
WH423D
Brand: Bard Pages: 26
Speck 00.5845 Operating Instructions Manual preview
00.5845
Brand: Speck Pages: 24
Waterax BB-4-D902 Quick Manual preview
BB-4-D902
Brand: Waterax Pages: 6
Geotech Bladder Pumps Installation And Operation Manual preview
Bladder Pumps
Brand: Geotech Pages: 32
Wacker Neuson PS3 1500 Operator'S Manual preview
PS3 1500
Brand: Wacker Neuson Pages: 52
Samoa LARIUS GIOTTO Operating Instructions Manual preview
LARIUS GIOTTO
Brand: Samoa Pages: 32
Aquascape Pro AquaSurge PRO 2000-4000 Instructions & Maintenance preview
AquaSurge PRO 2000-4000
Brand: Aquascape Pro Pages: 8

Brands by name

Popular brands

Load more brands