Agilent Technologies 5977B CI MSD Operating Manual Download Page 106

Page: 106 / 254

Operating in EI Mode



Operating the MSD from the 7890 GC Control Panel

106

5977B Series MSD Operating Manual

To view the firmware version of the MSD from the GC control panel

Press

MS/Aux Det

to bring up the 5977B MSD menu.

Press the down arrow to scroll to

Firmware

To view the serial number of the MSD from the GC control panel

Press

MS/Aux Det

to bring up the 5977B MSD menu.

Press the down arrow to scroll to

Serial#

To configure the network settings for the MSD from the GC control panel

Press

Config,

and then press

MS/Aux Det

to bring up the CONFIGURE MS

DETECTOR menu.

To configure the

IP:

parameter, use the GC keypad to enter the new IP

address for the MSD, then press

Enter

to complete the entry.

Wait for the GC to display the new IP address. Reboot the MSD or proceed to
the gateway address with the down arrow.

Press the down arrow to scroll to

GW:

and use the GC keypad to enter the

new gateway address for the LAN and press

Enter

to complete the entry.

Press the down arrow to scroll to

SW:

and use the GC keypad to enter the

new subnet mask for the LAN and press

Enter

to complete the entry.

Reboot the MSD. (See below.)

To reboot the MSD from the GC control panel

Press

Config,

and then press

MS/Aux Det

to bring up the CONFIGURE MS

DETECTOR menu.

Press the down arrow to scroll to

Request MSD Reboot?

Press

On/Yes

to reboot the MSD and wait for the MSD to complete this cycle

before trying to access it. The LED turns red until the reboot cycle is
completed.

Summary of Contents for 5977B CI MSD































































































































































































































































Search results

Summary of Contents for 5977B CI MSD

Reviews:

Related manuals for 5977B CI MSD

Brands by name

Popular brands

Agilent Technologies 5977B CI MSD, Operating Manual

Search results

Summary of Contents for 5977B CI MSD

Reviews:

Related manuals for 5977B CI MSD

Brands by name

Popular brands