Agilent Technologies 34945A User Manual Download Page 14 | Manualshive

Page: 14 / 124

background image

6

Agilent 34945A Microwave Switch/Attenuator Driver Module User’s Guide

1

About the Instrument

Table 1-2. Recommended Accessories for Agilent Switches/Attenuators
(Cont’d).

Y1157A - Y1159A Cable Assembly

Three cable kits are available for connecting switches and attenuators to the
Y115xA distribution boards:

Y1157A

Y1158A

Y1159A

The cable kits used with each switch/attenuator and distribution board are
identified in Table 1-2.

Attenuator

Model

Reference
Document

Number

(1)

Coil

Voltage

Option

Position

Indicator

Option

DC Connector

Option

Distribution Board

(number of

attenuators per

board)

(Cable Kit)

(3)

84904K - L
84906K - L
84907K - L

24V

(standard)

standard

10-pin DIP

(standard)

Y1153A (2)

Y1158A

84904M
84905M
84908M

024 standard

10-pin DIP

(standard)

Y1153A (2)

Y1158A

8494G - H
8495G - H
8496G - H

8495K
8497K

(4)

24V

(standard)

standard

12-pin Viking

(standard)

Y1153A (2)

n/a

(1) Product and technical overviews for the attenuators listed can be obtained by document number from the Agilent RF & Microwave Test Accessories
web site. Go to http://www.agilent.com/find/accessories, select ‘RF & Microwave Test Accessories’, and search for the document number.
Additional information can also be found in the “RF and Microwave Test Accessories Catalog” accessible from this site.

(3) These cables must be assembled to their connectors. Cable assembly instructions are provided in this chapter.

(4) Information on these attenuators plus additional information on the other attenuators can be found in the “RF and Microwave Test Accessories
Catalog” accessible from this site.

«
...
12
13
14
15
16
...
»

Summary of Contents for 34945A





























































































































Reviews:

No comments

Related manuals for 34945A

Brand: Keithley Pages: 66

Brand: Omega Engineering Pages: 3

Brand: Cabletron Systems Pages: 88

Brand: CAME Pages: 2

Brand: Pathway connectivity solutions Pages: 2

ATLONA Omega AT-OME-MS52W

Brand: Panduit Pages: 123

Atlona AT-OME-MS42

Brand: Panduit Pages: 86

Brand: Patton electronics Pages: 104

Brand: StarTech.com Pages: 10

Brand: GE Pages: 50

Brand: Eaton Pages: 2

Brand: Comprehensive Pages: 12

R-TEC Automation RTMWSR15C

Brand: Rowley Pages: 10

Brand: Labgear Pages: 8

Brand: T.I.P. Pages: 42

CT-HDVD-4X14K-SW

Brand: NB Pages: 23

Brand: IOGear Pages: 54

ScatterBox POE308

Brand: System Q Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands