manualshive.com logo in svg

Agilent Technologies 11645A Series, User'S And Service Manual

Share
Download
Agilent Technologies 11645A Series User'S And Service Manual Download Page 34

6-2

11645A

Replaceable Parts

Introduction

Introduction

The following tables list the replacement part numbers for the Agilent R11645A, Q11645A, 
U11645A, V11645A, and W11645A waveguide calibration kit contents. 

Table 6-6

 lists the 

replacement part numbers for items not included in the calibration kit that are either 
required or recommended for successful operation of the kit.

To order a listed part, note the description, the part number, and the quantity desired. 
Telephone or send your order to Agilent Technologies. Refer to 

“Contacting Agilent” on 

page 5-5

 for further information.

Table 6-1   Replaceable Parts for the R11645A WR-28

Description

Qty 

Per Kit

 Agilent 

Part Number

Attenuators

20 dB attenuator with data

1

11645-60021

50 dB attenuator with data

1

11645-60022

Airlines

50

Ω

 airline with data

1

11645-60016

25

Ω

 mismatch airline with data

1

11645-60011

Miscellaneous Items

Disk holder

1

5180-8491

Pad

1

11645-80026

Storage case

1

5181-5517

Storage box assembly

1

1540-0034

User’s and service guide

1

11645-90013

a

a.  

See “Printing Copies of Documentation from the Web” on page iii.

Verification data disk (8510)

1

11645-10006

Verification data disk (PNA)

1

11645-10019

Specification and performance verification disk 

1

08510-10033

Connector care

−

quick reference card

1

08510-90360

Hardware

Lock Washer

6

2190-0030

Hex Nut

6

2260-0002

Waveguide Alignment Pin (short)

6

11644-20009

Waveguide Alignment Pin (long)

6

11644-20006

4-40 Hex ball screw (0.75 inches)

6

3030-0721

3/32-inch hex ball driver

1

8710-1539

Summary of Contents for 11645A Series















































Reviews:

No comments

Brands by name

Popular brands

Load more brands