manualshive.com logo in svg

AGFA DRYSTAR AXYS, Service Manual

Share
Download
AGFA DRYSTAR AXYS Service Manual Download Page 88

 
 
DD+DIS033.07E 

Functional Description

 
 
 

 

DOCUMENT CONTROL NOTE: 

The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled. 

4 

Calibrations 

 

The following table lists the different Drystar Axys calibrations: 

 

Characteristic 

CDM 

TH profile 

Film 

Smart Profile 

Compliance Film 

Film printed 

 

 

 

 

Purpose of the 
calibration 

To determine new 
reference values for 
the CDM. This is 
done via an external 
densitometer. 

To reduce vertical 
macro banding 
(vertical density 
irregularities). Only 
macro density 
compensation is 
possible (in opposite 
to micro 
compensation in 
production). 

To measure the film 
sensitometry and to 
use these values for 
internal reference, so 
that the printer 
behaves linear 
regarding density 
reproduction. In 
addition, the 
maximum density is 
adapted. 

Equalization of TH 
resistor drift in the 
area of 10" film black 
borders when 
printing in mixed 
format conditions 
(mix of 10" and 14" 
print width). 

Make film calibration 
this accurate, that it 
passes the 
acceptance criteria 
as defined by 
Afssaps / EUREF: 
The default film 
calibration procedure 
is not necessarily 
accurate enough. 

To be done in 
following 
cases 

•

 Whenever the 

internal 
densitometer has 
to be adapted to 
an external 
densitometer (for 
image quality 
control) 

•

 If density 

reproduction 
check is not ok 

Unacceptable line 
artifacts visible in 
medical service test 
image 

•

 At maintenance 

•

 To compensate 

small density 
variations of the 
new film, when a 
new film package 
is used 

•

 During 

the 

troubleshooting 
procedure. Refer 
to chapter 3.3, 
Troubleshooting 

•

  In certain cases 

during 
maintenance. 
Refer to section 9, 
Maintenance 

•

 Before the 

Afssaps / EUREF 
acceptance test 

•

  Each 6 months, if 

the printer is 
under control of 
Afssaps / EUREF, 
and it did not pass 
the Afssaps / 
EUREF calibration 
check 

Automatic 
yes/no 

No 

No 

Yes, but only if 

switched on* 

No No 

* Automatic film calibration to be switched on via menu:  
  '2 Change settings - 5 Image Quality - 1 General - Select Default for Film Calibration 

 

 

 

Edition 1, Revision 1 

DRYSTAR AXYS 

Chapter 2 / 18 

06-2009 Type 

5367/100 

Agfa Company Confidentia

 

Summary of Contents for DRYSTAR AXYS














































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands