manualshive.com logo in svg

AGFA DRYSTAR AXYS, Service Manual

Share
Download
AGFA DRYSTAR AXYS Service Manual Download Page 68

 
 
DD+DIS033.07E 

Controls, Connections and Setup Procedure

 
 
 

 

DOCUMENT CONTROL NOTE: 

The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled. 

Edition 1, Revision 1 

DRYSTAR AXYS 

Chapter 1 / 32 

06-2008 Type 

5367/100 

Agfa Company Confidential

 

 

6 

Acceptance Test 

 

Purpose of the acceptance test: 

Proof of printer reproduction capability of image on the monitor. 

 

 

Console

5367_Reg01_002_e.cdr

Check according to criteria defined by 
National Acceptance Test Procedure

Drystar Axys

 

 

Figure 23 

 

(1) 

Perform the acceptance test according to national regulations: 

•

  Example for DRYSTAR AXYS Mammo in France:  

Acceptance test as defined by Afssaps / EUREF. For preparations refer to 
DRYSTAR AXYS Technical Documentation DD+DIS033.07E, Chapter 3.6, 
Adjustments and Calibrations. 

•

  Example for Germany: DIN6868 Part 56. 

 

 

NOTE: 

The German DIN6868 Part 56 is similar to the Image Quality Control procedure  
based on IEC1223-2-4. 

The Image Quality Control procedure based on IEC 1223-2-4 is described in the 
Hardcopy Application Manual  DD+DIS269.06E. 

 

Summary of Contents for DRYSTAR AXYS














































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands