manualshive.com logo in svg

AGFA DRYSTAR AXYS, Service Manual

Share
Download
AGFA DRYSTAR AXYS Service Manual Download Page 156

 
 
DD+DIS033.07E 

Repair and Service

Tools and Auxiliary Means

 
 
 

 

DOCUMENT CONTROL NOTE: 

The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled. 

 

3.7.1 

ADVP as DICOM print SCU 

 

ADVP as DICOM print SCU can be used to check the DICOM interface of the printer. 
In this case ADVP sends a test image to the printer. 

 

(1) Start 

ADVP 

(2)  Select 'Basic Grayscale' in the 

'Start up configuration' screen. 

(3)  Select 'Test - Print Film' 

(4)  Select 'SMPTE' (or any other 

test film). 

(5)  In the 'Configuration' window fill 

in Called (Printer) AE Title and 
'Printer IP address'. 

(6)  Select 'OK'. Now the desired 

test film is sent to the printer. 

 

 

Figure 51: ADVP as Print SCU 

 

3.7.2 

ADVP as DICOM print SCP (Print Emulator) 

 

 

ADVP as DICOM print SCP can be used to check the DICOM communication sent 
from the modality. ADVP in this case emulates the printer. The communication can be 
evaluated on site or by a product specialist in the GSC or RSC. 

 

Edition 1, Revision 0 

DRYSTAR AXYS 

Chapter 3.2 / 50 

10-2007 Type 

5367/100 

Agfa Company Confidential

 

Summary of Contents for DRYSTAR AXYS














































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands