manualshive.com logo in svg

AGCO LELY ATTIS PT 130, Operator'S Manual

Share
Download
AGCO LELY ATTIS PT 130 Operator'S Manual Download Page 79

5.1   Replace the transport wheel

WARNING: Risk of injury

Make sure that there are no persons in the area when you move the machine to the
transport position.

Procedure

1.

Push button 

 and lower the loader arm to the ground.

2.

Make sure that the transport wheel is not in contact with the ground.

3.

Make sure that you lock the clip (1) into pin

(2).

GUID-7B2C04B7-CD93-4BE9-8C1E-E95E370950F6-high.jpg [High]

Fig. 1  

4.

Remove clip (1) and pin (2) then rotate the

wheel assembly 180

o

.

GUID-8105BCD3-7514-479F-B888-1F94833EB963-high.jpg [High]

Fig. 2  

5.

Loosen and remove the wheel nuts and then

remove the transport wheel from the

machine.

GUID-AA4E2189-8B74-4899-A831-9ACF799EEF90-high.jpg [High]

Fig. 3  

GUID-EA6B9B7B-6E1D-44D0-9F65-1C105AD02703 [V1]

5. Troubleshooting

Bale Wrapper 

79

4820.LE.EN01

Summary of Contents for LELY ATTIS PT 130



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands