manualshive.com logo in svg

AGCO LELY ATTIS PT 130, Operator'S Manual

Share
Download
AGCO LELY ATTIS PT 130 Operator'S Manual Download Page 51

8.

If you have a bale tipper attached, move it to

the working position.
a) Remove the two pins and disconnect the

bale tipper bracket.

b) Lower the bale tipper to the ground.
c) Replace the bracket in the working

position and attach with the two pins.

GUID-D643846F-12CB-4FE6-AAD6-86C1F3E29A81-high.jpg [High]

Fig. 24  

GUID-B6C4AC69-EDB0-4BDC-9372-758054BDBED7-high.jpg [High]

Fig. 25  

3.4.2  Replace a film roll

WARNING: Risk of injury or death.

Always stop the engine and remove the ignition key before you do maintenance or
adjustments to the machine.

CAUTION: Risk of injury.

Keep your hands away from the top of the film
roll.

Procedure
1.

Push the lock down and pull the dispenser

away from the film roll until it engages with

the lock.

GUID-B08389FA-DF39-4B27-8C0F-D196611018BD-high.jpg [High]

Fig. 26  

GUID-9A69BDFE-8FA3-4C0E-AE62-3533AAED39EB [V1]

3. Operation

Bale Wrapper 

51

4820.LE.EN01

Summary of Contents for LELY ATTIS PT 130



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands