manualshive.com logo in svg

Afriso EURO-INDEX LAG-14 ER, Operating Instructions Manual, Page: 31 / 42

Share
Download
Afriso EURO-INDEX LAG-14 ER Operating Instructions Manual Download Page 31

 

Operation 

LAG-14 ER 

31 

The vent hole Ø 5 mm at the neck of the black LAG container must 

remain open. 

 

The system is ready for operation. 

6.  Apply voltage via the on-site mains fuse. 

 

The green pilot lamp lights up. 

7.  Have the specialised company certify the installation, commis-

sioning and test of the leak detector using the form in chap-

ter 17.1, page 38. 

7  Operation 

LAG-14 ER monitors double-walled containers (tanks). In the case of 

a leak, leak detection fluid escapes and LAG-14 ER triggers an 

alarm. The operation of LAG-14 ER is limited to its regular 

monitoring: 

•

 

The green pilot lamp is on. 

•

 

The red alarm lamp is not on. 

•

 

The audible alarm is off. 

7.1 

Alarm condition 

 

In the case of an alarm, refill leak detection fluid (mixed with wa-

ter in the specified mixing ratio) up to the indicated level. If the 

alarm repeats, there is a leak. 

 

The audible alarm can be muted by pressing the Acknowledge 

button. The red alarm lamp remains on. 

 

Immediately notify the installation company. 

Summary of Contents for LAG-14 ER











































Reviews:

No comments