Afag 50195031 Operating And Installation Instructions Download

Page: 5 / 27

R02.1

07/01/2021

Page 5

Safety instructions

Notes on symbols and instructions

Symbols:

Assembly and commissioning must be carried out by qualified per-
sonnel only and according to these operating instructions.

Please observe the meaning of the following symbols and notes. They are grouped
into risk levels and classified according to ISO 3864-2.

DANGER

Indicates an immediate threatening danger.

Non-compliance with this information can result in death or seri-
ous personal injuries (invalidity).

WARNING

Indicates a possible dangerous situation.

Non-compliance with this information can result in death or seri-
ous personal injuries (invalidity).

CAUTION

Indicates a possibly dangerous situation.

Non-compliance with this information can result in damage to
property or light to medium personal injuries.

NOTE

Indicates general notes, useful operator tips and operating rec-
ommendations which don’t affect safety and health of the person-
nel.

Summary of Contents for 50195031




























Search results

Summary of Contents for 50195031

Reviews:

Related manuals for 50195031

Brands by name

Popular brands

Afag 50195031, Operating And Installation Instructions

Search results

Summary of Contents for 50195031

Reviews:

Related manuals for 50195031

Brands by name

Popular brands