Installation Manual
1) Before you install this equipment, please read this full manual.
2) Ensure that there is good network reception at the location where it
will be installed.
Installation
Wiring
5) Install the antenna as high as
possible on the top of the pillar to
ensure line of sight in all directions for
best possible reception.
Keep antenna high as possible, and
above elect audio equipment
to eliminate interference
Side View
3) Remove the top two security
screws as shown. Do NOT remove
the bottom screws.
8) Ensure the
power is OFF
before inserting the SIM card.
9)
Carefully slide the SIM
holder
in the OPEN direction,
insert the SIM, and slide in the
CLOSED direction to lock it in
place.
Do NOT Force or use a
screwdriver!
11) Allow 20-30 seconds for the unit to boot up and detect the network.
Once successful connection has been made, the unit will sound a
confirmation tone and the GSM LED will begin flashing.
Programming Quick Start Guide
Programming is carried out by sending SMS texts to the unit.
3)
It is recommended to change the “no answer” time if there is more than 1
number stored. This stops the unit ringing a number after a set time, and can
be used to prevent voicemail answering the call. Send the following SMS..
The unit can allow up to 100 telephone numbers to be stored, for users to
be able to ring the system for automatic entry. This uses caller ID like a
phone to determine the identity of the caller. First, the unit must know what
country it is operating in.
4) Program the country code as follows..
GSM-3AB & ABK
GSM-3HB & HBK
V3.5 (1200 keypad)
1) First check reception. Send the following SMS to the unit...
2) Program the numbers you wish the unit to dial when the call button is
pressed, up to a maximum of 3 numbers. Each SMS must start with the pass
code, default 1234, in the following format *12*1234#, followed immediately
by a command. E.g to program the telephone number 0987654321, enter
the following SMS..
*20#
*12*1234#
11
0987654321
#
Pass code
Function code
Data
Up to 3 numbers can be sent together in a single SMS as
follows..
*12*1234#
11
tel.number1#
12
tel.number2#
13
tel.number3#
11 = Telephone number 1
12 = Telephone number 2
13 = Telephone number 3
*12*1234#
52
??#
Where ?? can be 2 digits from 10-99 seconds, default is 20.
*12*1234#
71
??#
Up to 3 numbers can be sent together in the same SMS. Just
add 72 then the number, then # each time. The pass code only
needs to be put at the beginning of each new messge.
5) Enter the telephone numbers required to have access control. Do not enter
country code, just the complete number as you would dial it..
*12*1234#
72
0987654321#
Where ?? can be 1-3 digits. For uk, insert 44, for Ireland 353, for
USA insert 1. Do not use any leading zeros.
Additional Programming Parameters
Remember to begin each new SMS with pass code *12*1234#
Entrance
Pillar
Speech
Unit
4-5 feet
minimum
200mm
min
The front door will hinge downwards
to allow access for mounting holes
and connection terminals.
Note: The protective film on the front
of the intercom should not be removed
until fully installed.
AC
AC
VCC
N
/C
COM
N/O
GND
PB
GND
DETECT
+
GSM
modem
Output
Optional
input limit
switch
from gate
Exit button
Call Button
Optional keypad
module
Hinge front door
Side View
4) Use appropriate wall fixings. 8-
10mm anchors, 75mm deep with M5
screw are recommended as a
minimum.
Antenna connector.
Finger tighten only!
SIM card
holder
Power LED
GSM LED
CPU LED
6) Carefully follow the
wiring instructions.
Additional wiring
suggestions for electric
strike lock and magnetic
lock are shown overleaf.
7) Register your SIM card
with the network, and check
it works in a mobile phone
first. If you are using a Pre-
pay or Pay&Go SIM, it will
need topped up first. Your
SIM should be GSM
compatible.
SIM card
If there is a fault or problem, the unit will emit a series of bleeps or warning
tones. If this occurs, check...
1) That the SIM card has been activated and has credit.
2) That the SIM card does not require a PIN code, disable this in a phone.
3) That the SIM card can make and received a call on a phone.
4) If the SIM card was purchased with a phone, that it is not locked to that
phone. Call the network operator to check.
5) Switch off power, remove and reseat the SIM card and try again.
10) After a final check of
wiring, switch on the power.
open
close
01
????
#
Change programming password.
1234
Code
Description
Default
Change access control password (allows users not in caller ID list
to call intercom and use pass code to activate relay).
5678
Change monitoring mode password (dial to listen in mode)
1212
Delete a button calling number, where
n
= number 1,2 or 3.
N/A
Speaker volume. Where
?
= level 0 - 3
Microphone volume. Where
?
= level 0 - 3
3
3
02
????
#
03
????
#
1n*#
3
?
#
4
?
#
51
?
#
Relay time. Where
?
= 1-9999 seconds.
1 sec
53
??
#
Max call time. Where
???
= 005-999 seconds (3 digit code)
60 sec
55
??
#
Max monitoring time (for listen in mode when calling the intercom)
00-60 mins. 00 = no limit.
10 min
57
??
#
Unit can call or SMS service number by set duration to prevent
SIM card deactivation if seldom used.
00-60 days. 00 = no inform.
00
65
?
#
Dial in mode for withheld numbers or non stored numbers. 1 =
answer the call & wait for pass code. 2 = answer the call &
automatically activate 2 way speech.
1
73
??
#
Delete phone number for caller ID access.
73*#
Delete all phone numbers for caller ID access.
N/A
N/A
77
number
#
Store service number to receive scheduled SMS or call from
intercom.
N/A
77*#
Delete service number.
999#
Restore defaults
N/A
N/A
-
12v dc
Check stored numbers. Note: no pass code needed for this
command. O = dial out number. I = Dial in number.
*21#
N/A
58
?
#
Choose between scheduled call to service number or send SMS to
service number. ?=1 for SMS, 2 for call.
1
Searching
Network found
Standby
Busy
1-12
Poor
13-20
Medium
21-31
Good
The unit should reply SIGNAL LEVEL = ?
Where ? will be between 1 and 31
Below 14 can cause problems with relay
operation, or no voice from the gate to the
house. Take action to improve reception.
+
Keypad Connections
(only keypad models)
-
12-24v
dc
N/C
COM N/O
N/C
COM
N/O
egress
OUT1 OUT2
OUT3
N/C
COM
N/O
K or A
DU out
(-)GND
Sense
INT Lock
Tamper
N/C
USA customers
– For some networks, you may need to enter the numbers with the long distance 1
before area code, then the number. E.g. 1-702-555-1234. Try it with and without to see method works.
ARCHITECTURAL
MODEL
HOODED
MODEL
O/P1 inhib
Note: PSU
should be
located
within 2
meters (6
feet)
LocksOnline Ltd
Tel +44 (0) 845 230 02 01 | Email [email protected]
www.locksonline.co.uk