Installation Manual
for
603AB, 603ABK, 603HB, 603HBK Wireless Intercom System
MENU
12.21
Charging
base
Entrance
Pillar
Transmitter / receiver - Keep
away from ground, as high as
possible. For best results, do
not install too close to sources
of electrical interference e.g.
gate automation panel
Speech
Unit
House or
reception
area
Note: Wood and glass only
reduce signal strength by
10-20%. Masonry will reduce
signal strength by 20-50%
per wall. Metal can totally
block signals.
For longer range
applications, locate the
handset near a window at
front of property.
150m
Typical
Installation
1) Before installing fully, test the range of the system. Wire the unit as per
wiring diagram, place the equipment in the desired location and test
operation.
2) Ensure that the gate transmitter / receiver unit is installed to facilitate
line of sight with the property or reception area. To achieve best results,
mount the unit as high as possible from the ground. Should you need to
extend range, you can mount it on a small pole to elevate it a few meters
from the ground.
3) It is recommended to charge the handset for 7-8 hours before use.
4) Power up the handset after inserting the batteries.
5) Wire the door station and transmitter / receiver according to the diagram
below..
Never drill holes in
the top of the
enclosure. Cable
entry should be
through the bottom.
Screened CAT 5
8 meters max
602 Range
Intercom
Transmitter
Mount AB model
to wall with
10mm x 50mm
large wall
anchors to
prevent removal
or theft.
-
+
12v
dc in
+
-
N/O
N/C
Shielded CAT5 cable
Solid
shield
wire
Volt free
Relay output
(4 sec pulse)
Code
button
Note: For improved audio
performance, the shield
wire can be connected to
bolts on metal housing of
speech panel.
Testing
1) Check all connections are correct before switching on the power.
2) Press the call button on the speech panel.
3) The handset should ring.
4) Press the button to answer the call and check two way speech.
5) Press to check the door / gate release function works.
Handset & Operation
Power
LED
ON/OFF
Vibration
ON/OFF
Voicemail
Symbol
Battery
Level
Reception
indicator
ADJUST VOLUME
Press or to adjust volume level,
and press MENU to select and save.
CHANGE RING TONE
Press and the unit will ring under
the currently select tone. Press
and to cycle through available
ring tones. Press MENU to select
and save.
CHANGE LANGUAGE
Press and the unit will display the
currently selected language.
1=English. Press and to
cycle. Press MENU to select and
save.
VOICEMAIL
When the door station is pressed, and not answered within 40 seconds,
the visitor can leave a message. Once complete, the handset will display
the symbol. Up to 16 messages can be saved.
To listen to voicemail, press MENU to play. If there are more than 1
message, press and to select the message required and press
MENU to play.
= Pause / Exit
= Continue
= Delete, long
press = delete all.
SET TIME ON DISPLAY
Press MENU for 2 seconds. The hour digits will begin flashing.
Press or to adjust. Press MENU to cycle from hour setting to
minutes and repeat. Press MENU a third time to exit and save changes.
Coding another handset to the System
Code
Button
Foil screening
wrapped
around MIC
wires for best
performance!
+
-
GND
MIC
connections
To add an extra handset to the system, follow the sequence below..
1) Press and HOLD the code button on the door station for 3 seconds,
until the LED’s on the bottom of the board start to flash.
2) Press and hold the Code button on the new handset ignoring the first
short tone, until you hear a confirmation tone (
“Di-Do-Do”). This may take
up to 10 seconds.
3) Once the door station lights stop flashing, then you can test the
system by pressing the call button on the door station. The new handset
should ring. If not, repeat the process from the top.
(keep short for better audio)
+ -
12v
dc
+
Keypad Connections
(ABK model)
-
12-24v
dc
N
/C
C
O
M
N
/O
N
/C
C
O
M
N
/O
e
g
re
s
s
OUT1 OUT2
Ver 3
1200 keypad model
C
Note: For earlier models, the existing master handset lights will
flash after step 1. You will need to press the MENU button on the
existing handset first, before proceeding to step 2 above.
OUT3
N/C
COM
N/O
K or A
DU out
(-)GND
Sense
O/P1 inhib
INT Lock
Tamper
N/C
Note: Keypad volt free output(s) needs connected to gate control panel or electric door
lock as well as relay output from the intercom controller PCB. Parallel connect C and N/O
contacts for electric gate controller or strike lock. Series connect C and N/C contacts for
magnetic lock.
3) Remove the top two security
screws as shown. Do NOT remove
the bottom screws.
The front door will hinge downwards
to allow access for mounting holes
and connection terminals.
Note: The protective film on the front
of the intercom should not be removed
until fully installed.
Call Button
Optional keypad
module
ARCHITECTURAL
MODEL
HOODED
MODEL