12v ac or
24v ac
Installation Manual
for
602AB, ABK, HB, HBK Wireless Intercom System
Entrance
Pillar
Base Station
(Keep away from
ground, as high as
possible)
Speech
Unit
House or
reception
area
Note: Wood
and glass only
reduce signal
strength by 10-
20%. Masonry
will reduce
signal strength
by 20-50% per
wall. Metal can
totally block
signals.
Never drill holes in
the top of the
enclosure. Cable
entry should be
through the bottom.
1) Before installing fully, test the range of the system. Wire the unit as
per wiring diagram, place the equipment in the desired location and
test operation.
2) Ensure that the gate base station is installed to facilitate line of sight
with the property or reception area. To achieve best results, mount the
base as high as possible from the ground. Should you need to extend
range, you can mount the base on a small pole to elevate it a few
meters from the ground.
Keep short as possible for best audio performance
S
P
E
A
K
8 meters max Shielded CAT5
Installation
Handset Coding
Microphone
connections
IMPORTANT:
Observe polarity!
For longer range
applications, locate
charging base near a
window at front of property.
300m
MAX
5) Wiring
Gate Base Station Connections
MIC
+
-
B
u
tt
o
n
0
V
1
2
V
PWR IN
0
V
1
2
V
602 Range
Intercom
Transmitter
Testing
Press the button on a handset to answer the call, and check for
two way speech. Press and HOLD the button to activate the door/
gate release function.
When the door station is powered on, the door station will attempt to ring
the handset(s). Provided the handset(s) and charging base are both
already on, and within range, the handset(s) should ring.
Master Base is a REPEATER. Locate
it in a strategic position.
The supplied handsets will already be coded to work with the door
station. Should you have purchased an additional handset individually,
please follow this procedure...
1) To register a new or additional handset, first put the charging base into
learn mode. To do this, press and hold the button on the bottom of
the charging base for 7 seconds or more, then release it..
2) On the new handset, press key.
3) Press or repeatedly to choose REGISTER, then press
to select.
U
p
to
2
0m
4) Press or to scroll through the base name list (1-4).
and press to select base 1.
5) If the base is found, and the handset has successfully registered, you
will be prompted to enter a pin code. The default is 0000.
The base will now assign a number to the handset, and the handset will
return to normal operation mode.
Base 1
Charger
charger
MASTER
Handset 1
Handset 2
Handset 3
Transmitter
Gate/Door Station Coding
The supplied gate/door station should already be coded with your master
base station. If for some reason the system does not work, or you
experience interference, it may be necessary to code the gate station.
1) On the master charging base station, press and hold button for 7
seconds (found underneath).
3) On the printed circuit board of the gate/door base station, you will find
a micro switch. Press and hold this button after the door station has made
2-3 ring tones.
If the process is unsuccessful, it may be necessary to clear the
previous coded door station (usually saved as HS2) from the master
base (see section below), and then repeat the steps above.
3) Power up the master charging base, then install the supplied Mi-MH
AAA batteries into the handset as shown. For best battery life, it is advised
to charge for 12 hours before use.
2) Switch on the power to the gate / door station, and it will begin
attempting to ring.
4) Continue holding the code button for at least 5-7 seconds. You should
hear a short melody De-Du-Do. This is confirmation of success.
Gate/Door Station
602 Range
Intercom
Transmitter
Short cable
602 Range
Intercom
Transmitter
Short cable
IMPORTANT:
Do not use 12v d.c. here.
For 12v d.c. connect to
PWR IN above. Switch
mode PSU not
recommended.
S
P
E
A
K
MIC
+
-
B
u
tt
o
n
a
.c
/
d
.c
+
a
.c
/
d
.c
-
Mains input if
optional
transformer
fitted.
Deleting a door station or handset
1) On a registered handset, press and then to scroll through
options until you reach BS SETTINGS.
2) Press to enter. You will see the option TERMINATE HS. Press
to select.
3) Enter the PIN code 0000 and press
4) Select the device you wish to delete and press to delete.
Connect CAT5
screen wire to 0V
Shielded CAT5
+ -
N
/C
C
O
M
N
/O
N
/C
C
O
M
N
/O
e
g
re
s
s
OUT1 OUT2
OUT3
N/C
COM
N/O
K or A
DU out
(-)GND
Sense
INT Lock
Tamper
N/C
Note: Keypad volt free output(s) needs connected to gate control panel or electric door
lock as well as relay output from the intercom controller PCB. Parallel connect C and N/O
contacts for electric gate controller or strike lock. Series connect C and N/C contacts for
magnetic lock.
1200 keypad model
4) Remove the top two security
screws as shown. Do NOT remove
the bottom screws.
The front door will hinge downwards
to allow access for mounting holes
and connection terminals.
Note: The protective film on the front
of the intercom should not be removed
until fully installed.
Call Button
Optional keypad
module
ARCHITECTURAL
MODEL
HOODED
MODEL
Mount AB model to
wall with 10mm x
50mm large wall
anchors to prevent
removal or theft.