background image

LED BATON

ROAD FLARE

ON/OFF BUTTON

MAGNET IN 

HANDLE BASE

MAGNET

CHARGING INPUT CONTACTS

BACK

FRONT

HOOK

Aervoe® LED Baton Road Flare #1154 & 1155

IMPORTANT SAFEGUARDS

Read all instructions before operating

• 

Do not look directly at the light; may cause injury to your eyes

• 

Never use if wiring or circuits are exposed or damaged

• 

Turn off all lights before charging

• 

Do not use alcohol, flammable solutions, or other solvents on or near this unit.  Only clean with 

• 

warm water and a soft cloth.
Administer close supervision when using around children

• 

Waterproof only when used in accordance with manufacturer’s instructions

• 

PARTS IDENTIFICATION

CHARGING

The Flare may be charged using either a 12V car charger, 120V wall charger, or USB adapter (included).

Plug the 

1. 

USB PlUg into the appropriate 12V or 120V ChARgiNg ADAPTeR, depending on your 

application, or directly into your computer or other USB charging device.  
Plug the male end of the 

2. 

USB CABle into the female port of the MAgNeTiC CONNeCTOR hUB.

Connect the MAgNeTiC CONNeCTOR 

3. 

hUB to the FlARe aligning the (+) and (-) terminal symbols on 

each.  The MAgNeT in the center and the divots in the screws will keep the two items connected and 
aligned.
Plug the 12V or 120V C

4. 

hARgiNg ADAPTeR into either a 12V power receptacle or 120V wall outlet.

green leD = charge in process

• 

Red leD = fully charged OR the Flare and hub are misaligned and need to be adjusted

• 

OPERATION

Press the ON/OFF BUTTON to rotate through the following 9 light patterns:

#1 - Rotate
#2 - Quad Flash
#3 - Alternating Blinks
#4 - SOS Rescue (Morse Code)
#5 - Steady on - high
#6 - Off

Alternate Operation:

To turn off the flare without cycling through the 5 light patterns, press and hold the ON/OFF BUTTON for 2 

seconds.  One leD will flash five times and then turn off.  When ready to operate again, press the ON/OFF 

BUTTON and it will return to the last flash pattern that was selected before turning off.

RANGE OF USE

emergency Road Flare

1. 

Replaces standard incendiary flares

• 

Use to alert drivers to potential roadside danger, mark detours, signal for help, 

• 

Safety Wand

2. 

Use as a hand-held signaling device to direct traffic (vehicle, crowds, aviation, marine), signal for 

• 

help
Used by emergency services, airport ground crews, road construction crews and personal 

• 

vehicle safety

Features

3. 

Safer and ecologically better for our environment than flame style emergency road flares.  No 

• 

spark, open flame, fumes or toxic chemicals are produced when using as a road flare.
Shock resistant construction makes it very durable and can withstand the impact of roadside 

• 

traffic.  Can even be run over by a truck and still operate.  Used by fire, police, and other 
emergency responders.
Waterproof so it may be used for marine applications and safely in wet environments, including 

• 

submerged to a depth of 50 feet.  Will float unless secured.
Using the magnet on the back or handle end, attach to any ferrous metal surface.  Place on a 

• 

vehicle, fence, or other metal surface.
lie flat or upright on it’s handle end for vertical placement.  Place on the road, at construction 

• 

sites, vehicle bumper or other surface, and anywhere needing emergency signaling.
Optional Flex-Fit Tripod #1159 is available to hold Flares in a vertical position for greater visibility, 

• 

even on uneven ground.  Contact your local retailer or www.aervoe.com.

NOTe:  it is not recommended that you disassemble the Flare.  if it is not reassembled correctly it may result 
in failure of the waterproof seal and damage to the unit.

Reviews: