background image

16

 

RMS Clamp-on Simple Logger® Model CL600

Limited Warranty

The  Simple  Logger

®

  CL600  is  warranted  to  the  owner  for  a  period  of 

two

 

year

s

 from the date of original purchase against defects in manufacture. This 

limited warranty is given by AEMC

®

 Instruments, not by the distributor from 

whom it was purchased. This warranty is void if the unit has been tampered 

with, abused or if the defect is related to service not performed by AEMC

®

 

Instruments. 

For  full  and  detailed  warranty  coverage,  please  read  the  Warranty 

Coverage  Information,  which  is  attached  to  the  Warranty Registration 

Card  (if  enclosed)  or  is  available  at  www.aemc.com.  Please  keep  the 

Warranty Coverage Information with your records.
What AEMC

®

 Instruments will do:

If  a  malfunction  occurs  within  the 

warranty

 period,  you  may  return  the  in

-

strument  to  us  for  repair,  provided  we  have  your  warranty  registration 

in

-

formation  on  file  or  a  proof  of  purchase.  AEMC

®

 Instruments  will,  at  its 

option, repair or replace the faulty material.

REGISTER ONLINE AT:

www.aemc.com

Warranty Repairs

What you must do to return an Instrument for Warranty Repair: 

First,  request  a  Customer  Service Authorization  Number  (CSA#)  by  phone 

or by fax from our Service Department (see address below), then return the 

instrument along with the signed CSA Form. Please write the CSA# on the 

outside of the shipping container. Return the instrument, postage or shipment 

pre-paid to:

Ship To:

  Chauvin Arnoux

®

, Inc. d.b.a. AEMC

®

 Instruments

15 Faraday Drive • Dover, NH 03820 USA

Phone: (800) 945-2362  (Ext. 360)

(603) 749-6434  (Ext. 360)

Fax:  (603) 742-2346 or (603) 749-6309

E-mail: [email protected]

Caution:

 To protect yourself against in-transit loss, we recommend you insure 

your returned material.

NOTE: You must obtain a CSA# before returning any instrument.

Summary of Contents for Simple Logger CL600





















Reviews: