AEMC instruments 2153.61 User Manual Download

Page: 25 / 36

Data Logger Model DL913 & DL914

If your computer has an earlier version of the software installed, the

InstallShield program will:
•

Ask you to confirm the installation of the software (click

Next

to confirm)

• Display a status bar to indicate the installation’s progress
• Inform you when the program is installed

9. Click

Finish

to install the next selected program.

A message will appear and inform you when the programs are installed.

10. Click

Finish

to return to the Setup screen.

11. Select any additional installation options located in the lower left corner.

Adobe Reader:

sends you to the Adobe website to download Adobe

Acrobat Reader, which is necessary for PDF documents.

Firmware Upgrades:

sends you to your instrument’s firmware download

page on AEMC

Instruments website after you select the instrument type.

User Manuals:

shows you a list of user manuals available on the USB.

12.

When finished, click

Exit

The DataView folder will appear on your desktop and contain icons for the

installed Control Panels.
After the Control Panel is installed, you can connect your instrument to the

computer to configure the instrument, configure recording parameters, schedule

recording sessions, start recording sessions, and download the recorded data to

the computer for analysis and report generation.

5.2 TYPES OF CONNECTIONS

The instrument provides three connection options:

■

USB

■

Wi-Fi via router

■

Wi-Fi Direct

5.2.1 USB Connection

Connect the instrument to the computer using the provided USB.

If the instrument is being connected for the first time:

1. In the Data Logger Control Panel, select

Instrument

in the menu bar.

2. Click

Add an Instrument

3. Go through the screens for the Add an Instrument wizard.

Use the

Help

button if you need further instructions.

4. When prompted to select the connection type, choose

USB

5. After completing all screens, press

Finish

to exit the Add an Instrument

wizard.

The connected instrument will appear on the left side of the screen in the Data

Logger Network frame.
A green check mark next to the instrument’s name indicates that it is connected.

Summary of Contents for 2153.61





































Search results

Summary of Contents for 2153.61

Reviews:

Related manuals for 2153.61

Brands by name

Popular brands

AEMC instruments 2153.61, User Manual

Search results

Summary of Contents for 2153.61

Reviews:

Related manuals for 2153.61

Brands by name

Popular brands