background image

• You activate the appliance (special

short tune).

• You deactivate the appliance (special

short tune).

• You touch the buttons (click sound).

• You make a wrong selection (3 short

sounds).

• The programme is completed

(sequence of sounds for about 2

minutes).

• The appliance has a malfunction

(sequence of short sounds for about 5

minutes).

To deactivate/activate the acoustic

signals when the programme is

completed, touch the Stains/Prewash

and the Anti-Allergy buttons

simultaneously for about 6 seconds.

If you deactivate the

acoustic signals, they

continue operate when the

appliance has a malfunction.

10.4 Permanent Extra Rinse

With this option you can permanently

have an extra rinse when you set a new

programme.

• To activate/deactivate this option

touch the Stains/Prewash button and

the Rinse button simultaneously until

the indicator of the Extra Rinse button 

comes on/goes off.

10.5 Soft Plus 

Set the Soft Plus option to optimise the

fabric softener distribution and improve

the fabric softness.
It is suggested when you use the fabric

softener.

This option increases slightly

the programme duration.

To activate/deactivate this option touch

the Temp. button and the Spin button
simultaneously until the   indicator 
comes on/goes off above the 

indicator.

11. BEFORE FIRST USE

During installation or before

first use you may observe

some water in the appliance.

This is a residual water left

in the appliance after a full

functional test in the factory

to ensure the appliance is

delivered to customers in

perfect working order and is

no cause for concern.

1. Make sure that all transit bolts have

been removed from the appliance.

2. Make sure that the electrical power is

available and the water tap is open.

3. Pour 2 litres of water into the

detergent compartment marked by

.

This action activates the drain system.

4. Pour a small quantity of detergent

into the compartment marked by 

.

5. Set and start a programme for cotton

at the highest temperature without

any laundry in the drum.

This removes all possible dirt from the

drum and the tub.

12. DAILY USE

WARNING!

Refer to Safety chapters.

12.1 Activating the appliance

1. Connect the mains plug to the mains

socket.

2. Open the water tap.

ENGLISH

23

www.devicemanuals.eu/

Summary of Contents for L7FEE865R

















































Reviews: