AEG L 98699 FL Page 4 User Manual Download

Page: 4 / 40

• If the supply cord is damaged, it must be replaced by

the manufacturer, its service agent or similarly quali-
fied persons in order to avoid a hazard.

• The operating water pressure (minimum and maxi-

mum) must be between 0,5 bar (0,05 MPa) and 8 bar
(0,8 MPa)

• The ventilation openings in the base (if applicable)

must not be obstructed by a carpet.

• The appliance is to be connected to the water mains

using the new supplied hose-sets. Old hose sets must
not be reused.

SAFETY INSTRUCTIONS

2.1

Installation

• Remove all the packaging and the

transit bolts.

• Keep the transit bolts. When you

move the appliance again you must
block the drum.

• Do not install or use a damaged appli-

ance.

• Do not install or use the appliance

where the temperature is less than 0
°C or where it is exposed to the
weather.

• Obey the installation instruction sup-

plied with the appliance.

• Make sure that the floor where you in-

stall the appliance is flat, stable, heat
resistant and clean.

• Do not install the appliance where the

appliance door can not be fully
opened.

• Always be careful when you move the

appliance because it is heavy. Always
wear safety gloves.

• Make sure that there is air circulation

between the appliance and the floor.

• Adjust the feet to have the necessary

space between the appliance and the
carpet.

Electrical connection

WARNING!

Risk of fire and electrical shock.

• The appliance must be earthed.
• Make sure that the electrical informa-

tion on the rating plate agrees with
the power supply. If not, contact an
electrician.

• Always use a correctly installed shock-

proof socket.

• Do not use multi-plug adapters and

extension cables.

• Make sure not to cause damage to the

mains plug and to the mains cable.
Should the appliance power supply
cable need to be replaced, this must
be carried out by our Service Centre.

• Connect the mains plug to the mains

socket only at the end of the installa-
tion. Make sure that there is access to
the mains plug after the installation.

• Do not pull the mains cable to discon-

nect the appliance. Always pull the
mains plug.

• Do not touch the mains cable or the

mains plug with wet hands.

• This appliance complies with the

E.E.C. Directives.

www.aeg.com

Summary of Contents for L 98699 FL









































Search results

Summary of Contents for L 98699 FL

Reviews:

Related manuals for L 98699 FL

Brands by name

Popular brands

AEG L 98699 FL, User Manual

Search results

Summary of Contents for L 98699 FL

Reviews:

Related manuals for L 98699 FL

Brands by name

Popular brands