4
4
product on a combustible surface.
■
Do not use the product near flammable materials, such as
cloth, packaging materials, paint, spray paint or aerosols,
lubricants, thinners, petrol containers, gas containers, or
gas appliances.
■
Do not cover any ventilation slots and provide adequate
ventilation during operation.
■
Never modify, disassemble, or attempt to repair the product
yourself.
■
Do not allow the charger or battery packs to become
contaminated with any material that could be conductive,
such as, metallic particles from grinding, cutting, or
machining processes.
■
Remove the plug of the product from the power socket
when it is not in use or when cleaning it.
■
Only use extension cable that is approved and in good
condition.
■
Do not charge battery packs that show signs of leaks.
Dispose of them properly.
■
Never charge a damaged battery pack. If damaged,
replace immediately.
■
If the supply cord is damaged, it must be replaced by a
special cord or assembly available from the manufacturer
or its service agent.
WARNING! Do not insert any object into the ventilation
slots or charging connector.
This can cause damage to the
appliance and may increase the risk of personal injury and
property damage.
WARNING! Do not alter or modify the unit from the
original design or function.
This may increase the risk of
serious personal injury or property damage.
WARNING! Before you plug in your product, make
sure that the supply voltage used corresponds to that
indicated on the rating plate.
SPECIFIED CONDITIONS OF USE
The charger is only intended to charge 58V AEG Li-ion battery
packs listed in this manual.
The product is only for use indoors in dry conditions.
The product is not intended to charge any other type of battery
or be used as a power supply or any other purpose. It should
never be used in explosive or inflammable environments.
Do not use the product for any other purpose.
DESCRIPTION
1. LED indicators
2. Battery port number
3. Battery port
4. USB charging port
5. Cell phone holder
6. Battery pack
7. Latch release button
ENVIRONMENTAL PROTECTION
Recycle raw materials instead of disposing
of them as waste. The product, accessories,
and packaging should be stored for
environmentally friendly recycling.
OPERATION
WARNING! Do not allow familiarity with products to
make you careless.
Remember that a careless fraction of a
second is sufficient to inflict serious injury.
WARNING! Do not use any attachments or accessories
not recommended by the manufacturer of this product.
The use of attachments or accessories not recommended can
result in serious personal injury.
WARNING! Never operate the charger where there is
a possibility of inflammable or explosive gases or vapour.
Keep well away from petroleum, paint and cleaning supplies,
and gas-fired heating systems.
WARNING! Charge in a well-ventilated area.
Do
not block charger vents. Keep them clear to allow proper
ventilation.
CHARGING THE BATTERY PACK
Battery packs are shipped in a low charge condition to prevent
possible problems. Therefore, you should charge them before
first use. If the charger does not charge your battery pack
under normal circumstances, bring both the battery pack and
charger to an authorised service centre.
NOTE:
When multiple battery packs are connected to the
charger, the battery packs are charged two at a time. The
batteries will be charged in the order they are placed. Batteries
placed on the same side (side 1 or side 2) will be charged
simultaneously.
Make sure the power supply is normal household voltage, 220
– 240V, 50Hz, AC only.
NOTE:
After charging is complete, the green LED will remain
on until the battery pack is removed from the charger, or
charger is disconnected from the power supply.
The battery pack will become slightly warm to touch while
charging. This is normal and does not indicate a problem.
Do not place the charger and battery pack in an area of extreme
heat or cold. They will work best at normal room temperature.
NOTE:
The charger and battery pack should be placed in a
location where the temperature is more than 10°C but less than
38°C.
CHARGING A HOT BATTERY PACK
When using a tool continuously, the battery pack will become
hot. A hot battery pack may be placed directly onto the charger
port, but charging will not begin until the battery temperature
cools to within the acceptable temperature range. When a hot
battery pack is placed on the charger, the red LED will be on,
and the orange LED will begin flashing. When the battery pack
cools, the charger will automatically begin charging.
